ABOUT

Solutions & Cases

Our Case
  • How to Solve Common Concrete Problems in Construction

    20/11/2019· One of the most repeated problems in concrete is crazing. Crazing occurs when the surface shows several interconnected fine cracks or when the cement paste comes up to the surface and shrinks. Although the concrete strength probably is not affected, cracks will show up when the slab is damp. How to avoid crazed concrete:

  • A survey on problems encountered in current concrete

    01/06/2018· In order to better understand the problems encountered during the construction of today’s concrete structures in the UK and the degree to which concrete cracking/damage is a major problem, a piece of market research was commissioned by the Materials for Life (M4L) EPSRC funded research project . The three main objectives of this market research were to identify:

  • Concrete Production an overview ScienceDirect Topics

    Concrete production is now, of course, a mature technology. The ancient Greeks and Romans both produced mortars that may be considered to be the forerunners of today’s concretes, while “modern” concretes have been in use since the middle of the 19th century. These concretes now constitute a highly sophisticated family of materials. Portland cement itself is a complex material

  • (PDF) Environmental aspect of concrete: Problems and

    However, the production of cement, a primary constituent of concrete is a significant source of global carbon dioxide (CO 2) emissions, making up approximately 2.4 percent of global

  • How To Avoid Common Problems During Concreting at Site?

    Understanding the common concreting problems that can occur during concreting practice will help to minimize further mistakes during concreting. Most of Understanding the common problems that can occur during concreting practice will help to minimize further mistakes during concreting. Most of the concreting problems arise due to:Improper MixingImproper PlacingImproper CuringMentioned below

  • Problems and failures Prestressed Concrete Bridges

    07/07/2015· Prestressed Concrete Bridges; Problems and failures Open PDF. Prestressed Concrete Bridges. Next > Prev Concrete and reinforcement. Problems during construction. Structural behaviour problems. Problems after opening. References. Full Text References. Related content . Definitions. Source: Prestressed Concrete Bridges, 1 Jan 2012 (361–362) Problems and failures.

  • Concrete Design & Production Portland Cement Association

    Ultra High Performance Concrete (UHPC), also known as reactive powder concrete (RPC), is a high-strength, ductile material formulated by combining portland cement, silica fume, quartz flour, fine silica sand, high-range water reducer, water, and steel or organic fibers. The material provides compressive strengths up to 29,000 psi and flexural strengths up to 7,000 psi.

  • Concrete Production Process| marstllaroilconcrete

    26/07/2016· Concrete floors can have a wide variety of finishes and textures. This means each floor can have a one-of-a-kind appearance. When we pour concrete for a floor, we often use a fine aggregate mix and incorporate color. During the finishing process, the concrete can be scored, stamped or textured. This helps to create a tiled or textured look.

  • Production issues, and what can be done about them

    During the manufacturing process, there are many production issues that can occur: poor quality, long lead times, high on-hand inventory, supply chain interruptions, etc. These things all affect the product you’re putting out there, which in turn affects the public’s perception of your brand. The big 4

  • Concrete: the most destructive material on Earth Cities

    25/02/2019· Taking in all stages of production, concrete is said to be responsible for 4-8% of the world’s CO2. Among materials, only coal, oil and gas are a

  • The problem with reinforced concrete

    Reinforced concrete is everywhere. But unlike plain concrete, which can last for centuries, reinforced concrete can deteriorate in decades as the reinforcing bars succumb to rust.

  • Factors affecting durability of concrete • Aggregate

    The production of new building materials depletes natural resources and can produce air and water pollution The design service life of most buildings is often 30 years, although buildings often last 50 to 100 years or longer. Most concrete and masonry buildings are demolished due to obsolescence rather than deterioration. A concrete shell can be left in place if a building use or function

  • Manufacturing Problems and Solutions Creative

    Problems that arise during manufacturing present some of the most frustrating areas in the product development process. This is especially true for injection molded products. The development process for injection molded products is usually long and arduous. By the end of that process, you’ve spent a lot of time and money on development and tooling. Now you face a production deadline that

  • Concrete Slab Surface Defects: Causes, Prevention, Repair

    Warm the subgrade before placing concrete on it during cold weather. 4. Avoid placing a slab directly on polyethylene film or other vapor barriers. Use a 100-mm (4-in.) layer of compactible, drainable fill (not sand). A “crusher run” material, usually graded from 38 mm to 50 mm (1-1/2 in. to 2 in.) down to rock dust, is suitable. Following compaction, the surface can be choked off with a

  • (PDF) Common Drilling well problems (Reasons,

    Problems encountered during drilling are discu ssed with particulars in. order to give a better understanding to the complications involved with. the operation. And fo r progress, more ef fective

  • Batching, Mixing, Transporting, and Handling Concrete

    delay time during concrete placement. Early Stiffening and Drying Out. Concrete begins to stiffen as soon as the cementitious materials and water are mixed, but the degree of stiffening that occurs in the first 30 minutes is not usually a problem; concrete that is kept agitated generally can be placed and compacted within 1. 1 ⁄ 2

  • Problems I have Encountered in the Process of making my

    09/02/2016· Pre Production One of the main problems I have faced in my pre production is that of getting familiar with the layouts and details of the forms that you have to fill in. For example, when you're filling out location recces. Also another problem I encountered was that

  • Inspection during production: a necessity

    A factory might identify some problems, hide them away from the inspector, and then ship them out. This is why an inspection during production should be followed by a final random inspection, to confirm average quality. Second, for sensitive projects, the factory might need some guidance from the beginning of production. This is the work of a

  • 5 Major Problems of Agriculture and their Solutions

    Problems in Agriculture Sector and Practical Solutions. Agriculture was and will always be one of the most important occupations since it is responsible for feeding the world and providing sustenance. However, due to modernization and the ever-increasing population, agriculture is facing some hurdles lately. These issues are impacting the production of agricultural crops both in qualitative as